Fishing Reels Gear Ratios Explained

1st, a working feature of gears that’s important for bass fishermen to understand, in relation to fishing reel gear percentage and how it relates to their reel’s performance, is that you can’t increase speed or power without decreasing the other. Gearing up, that is, rising the number of complete revolutions speed of the spool per crank of the handle, will decrease its power and vice-versa. Decreasing the number of revolutions increases power but decreases speed. This is where fishing reel gear percentage comes in. Low gear percentage equals power, high gear percentage means speed. Think, race cars go fast but can not pull any weight while big trucks can pull heavy loads but can only move gradually. (bassfishingandcatching.com)

A reel with a 6. 2:1 gear percentage and a 1. 5-inch-diameter spool will recover less than 11 inches of line per turn of the handle. The reel with 6. 2:1 percentage could be called a high-speed model established strictly on numerical gear percentage, and the reel with 4. 4:1 percentage could be called a low-speed model. Still the 4. 4:1 reel will move a lure through the water at a faster speed per turn of the reel handle. The bottom line is that the size of the spool also as the amount of line on that spool in mix with gear percentage is what affects line recuperation. (fishing.about.com)

Turning the handle on a fishing reel engages a flat, round spur gear, that is on the interior shaft of the handle. Teeth on the spur gear are exactly machined to interact with a smaller gear that is on the center shaft of the reel spool. In most reels this is a helical gear, which is shaped like a small, hollow barrel. Disengaging the free spool lever shifts the spur gear away from the helical gear, which lets the spool to rotate freely when casting. Engaging the lever shifts the spur gear back into position where it interlocks with the helical gear. The diameter of the spur gear and helical gear are proportionate to the gear percentage of a specific fishing reel. (livestrong.com)

Hays 101 gave you a good explanation of the applications of those two common reel speeds. Just, the reduce the number, the reduce the gear percentage. The higher the number, the higher the gear percentage. What is that means is that lower gear percentage reels retrieve line at a slower rate than higher gear ration reels. The different speeds lend themselves to individual methods, as hays 101, illustrated. NIB High Football Rules!!!. (answers.yahoo.com)

   As with most of your bass fishing equipment, correct maintenance can make all of the difference in satisfactory performance. Reels should be wiped down after each use and stored in a dry place. It’s suggested that reels be disassembled and cleaned at least once a year. Rods should be inspected on a regular basis for cracked or broken guides and cracks or nicks in the rod. Rods should be stored in a rod box or rod holder between uses. (bassresource.com)

Brass is the common gear material in baitcasting reels, although aluminum and stainless are used. Zinc is the common in spinning reels, again with aluminum and stainless as alternatives. Stainless steel is common in regular reels. Each metal has a drawback. Aluminum gears are super light, although they don t take abuse well. Brass is stronger, however it s not as strong as stainless steel. Stainless is the strongest, however it does lack smoothness. Still, all these different gears can work well, contingent on the species targeted. (sportfishingmag.com)

When spooling line on a spinning rod, lay the spool on the floor so that the line is leaving the spool in the same direction that it’s going onto the reel. To test if the line is going on properly, pinch the line between your thumb and forefinger and make a dozen cranks of the reel handle. Then, stop winding line and drop the rod tip to put slack in the line. If the line starts to turn and turn, then you’re putting it on in the wrong direction. Simply flip the spool over and continue to fill the reel. (takemefishing.org)

Drag systems let tension to be placed on the spool. Just like brake systems, drag system in baitcast reels differ therefore to make and model. typically, the drag is on the side of the reel in a star-shaped wheel. They aren’t call professional anglers without a reason. Recreational anglers have a tendency to break off fish when fighting them to the ship; pros get them to and in the ship. McClelland revealed, I can not remember the last time I broke off a fish in open water. that’s remarkable, however McClelland replied, If you set your drag as indicated by the size of line you’re using and if you re reel has a quality, smooth drag system like the Quantum PT series reels, you’ll have fewer fish break off. (bradwiegmann.com)

Maple spinning reels have been intended with the factors in mind. Our range of smaller 1000 2000 sized reels will frequently have higher gear ratios simply to overcome the smaller spools and handles shown on these reels, whereas our bigger spinning models feature lower gear ratios to ensure that you still have enough low down torque to manage bigger species. But regardless what style of fishing your into, there’s a Maple model that will suit you application and budget. (Check out your url)

Action mentions the flex characteristics of a rod, in other words how much the rod bends when you put pressure on the tip and how far the rod flexes. Action varies from extra fast where just the tip flexes to slow or softer where the most of the rod flexes. Fast action rods are the best choice when the fishing technique requires the sensitivity of feeling light biting fish or when fishing for big game fish in heavy cover and weeds where the key is to setting the hook fast with just a snap of the wrist moving the fish s head up and away. For example, fast action light rods were used for jigs, soft plastic worms or twitching minnow/shad shaped crank baits for bass and walleye. (walleye411.com)